TOOL HOLDERS

Tap Holder – Model 2747-116-SA

This holder is the non-releasing type. Provision is made for using a 5/8” diameter bushing 7/8” long. Body length: 1-5/8”.

Drill Holder – Model 2714-SA

Solid-type drill holder can be used either rotating or stationary. Provision is made for using a 5/8” diameter drill bushing 7/8” long. Adjusting screw is provided in shank to prevent drill from slipping back. Body length: 1-1/8”

Drilling and Chamfering Tool Holder – Model 2714-IR-SA

A drill holder with provisions for a 5/8” x 5/16” blade which is set on a 45° angle for chamfering. It can also be supplied with an auxiliary facing tool plate which takes a 5/16” x 3/8” blade for finish facing. Provisions are also made for using a 5/8” diameter drill bushing 7/8” long. Body length: 1-3/4”

Drill Holder with Stock Stop – Model 2716-SA

This holder is designed for the first position. A hardened stock stop plate is furnished. Provision is made for using a 5/8” diameter drill bushing 7/8” long. Adjusting screw is provided in shank to prevent drill from slipping back. Body length: 2-3/16”.

Adjustable Drill Holder – Model 2717-SA

Solid type drill holder can be used either rotating or stationary. Provision is made for using a 5/8” (15.88 mm) diameter drill bushing 7/8” (22.23 mm) long. Adjusting screw is provided in shank to prevent drill from slipping back. Body length: 11/8”(28.58 mm).

Centering & Facing Tool Holder – Model 2720-SA

A solid drill holder with provision for blade to be used for facing. Provision is made for a 5/8” (15.88 mm) diameter drill bushing 7/8” (22.23 mm) long and a 3/8” (9.53 mm) square tool bit. A stock stop plate is furnished for use in the first position, which will permit the use of a form tool in the front cross slide. Holder can also be used in any other position. Adjusting screw in shank is provided to prevent drill from slipping back. Body length: 2 7/16” (61.91 mm).

Sizing Tool Holder Regular / Oversize – Model 2726-R-SA / Model 2726-O-SA

2726-R-SA: The capacity of this sizing tool holder is .075” to .500” (1.90 to 12.70 mm) diameter, 3/4” (19.05 mm) wide. It uses a circular tool and roll, which are made to suit the work. The tool and roll swing to insure same size work from all spindles. Sensitive adjustments are provided to obtain a high degree of accuracy. Width of holder is 13/8” (34.93 mm).

2726-O-SA: Same as 2726-R-SA except capacity is .262” to .812” (6.65 to 20.62 mm) diameter, 3/4” (19.05 mm) wide. Width of holder is 13/8” (34.93 mm).

Knurl Holder – Model 2729-SA

This is a single knurl holder for knurls 5/8” (15.88 mm) diameter, 1/4” (6.35 mm) wide with a 1/4” (6.35 mm) hole. Width of holder is 3/4” (19.05 mm).

Knurl Tool Holder Double – Model 2730-SA

This holder uses two knurls for either diamond or straight knurling. Knurl roll sizes for this holder are 5/8” (15.88 mm) diameter, 1/4” (6.35 mm) wide with a 1/4” (6.35 mm) hole. Width of holder is 11/4” (31.75 mm). This holder is also used for straightening.

Knurl Tool Holder Wide, Oversize – Model 2730-23-SA

This holder uses two knurls for either diamond or straight knurling. Knurl roll sizes for this holder are 3/4” (19.05 mm) diameter, 3/8” (9.53 mm) wide with a 1/4” (6.35 mm) hole. Width of holder is 1 1/4” (31.75 mm). This holder is also used for straightening.

Rectangular Cutoff Tool Holder – Model 2768-SA

This holder will accommodate all standard cut off blades from 1/32” (0.80 mm) to 1/8” (3.18 mm). The overall width of this holder is 5/8” (15.88 mm).

Blade Cutoff Tool Holder – Model 2768-T-SA

This holder will accommodate all standard width T blade cut off tools.

Stock Stop – Model 2810-SA

This stock stop attaches to a special tool clamp ring which is supplied. The assembly travels with the tool spindle. It is used generally with hollow mill in the first position. Furnished shank is 5 1/4” (133.35 mm) long to be turned to length required to suit hollow mill used.

Adjustable Drill & Facing Tool Holder – Model 2763-10-SA

This holder is an adjustable drill holder with provision for a blade to be used for facing. Drill can be centered independently of blade. Provision is made for using a 5/8” (15.88 mm) diameter drill bushing 7/8” (22.23 mm) long and a 3/8” (9.53 mm) square tool bit. A stock stop plate is furnished for use in the first position which will permit the use of a form tool in the front cross slide.

Holder can be used in any other position. Adjusting screw in shank is provided to prevent drill from slipping back. Body length: 2 7/16” (61.91 mm).

Box Tool Holder – Model 2785-1-SA

Turning capacity of the box tool is 9/64” (3.57 mm) to 11/32” (8.73 mm) x 2 1/2” (63.50 mm) long or 11/32” (8.73 mm) to 1/2” (12.70 mm) diameter x 1 1/2” (38.10 mm) long. Provision is made for a 3/8” (9.53 mm) square tangent tool which can be set .015” (0.38 mm) ahead of the rolls or .110” (2.79 mm) behind the rolls. The tool holder is designed for the first position, being equipped with a stock stop, but can be used in any position. Two sets of roller rests, mounted on swinging arms are furnished. Shank is drilled for 3/8” (9.53 mm) center drill. Body length: 2 1/8” (53.98 mm).

Adjustable Drill Holder – Model 2862-10-SA

This is a short holder which clamps on the outside diameter of the 1 3/8” (34.93 mm) tool spindle for long work. This can be clamped on the outside of an E-2714 drill holder for short work. Provision is made for using a 5/8” (15.88 mm) diameter drill bushing 7/8” (22.23 mm) long. Length of holder body beyond end tool spindle is 7/8” (22.23 mm)

1st Position Dovetail Tool Holder – Model 3060-SA

This 1st position dovetail tool holder is designed for heavy cuts. This holder has a 10º face angle so the cutting tool is ground with a 10º angle plus the desired rake angle. The tool is set at approximately 10% of the smallest diameter ahead of center (above center). An American standard dovetail blank group #2, with a 1/4-20 NF tapped hole for a set screw is used. This screw takes the thrust as well as making the tool easy for adjustment.

Dovetail Tool Holder – Model 3060-10-SA

The same basic design as our 3060-SA with a 10º face angle with two tie down bolts for extra stability.

2nd Position Dovetail Tool Holder – Model 3092-5-SA

The same basic design as our 3060-SA with a 10º face angle with two tie down bolts for extra stability.

Self Centering Tool Holder – Model 3096-SA